what kind of stain to you put on kitchen butcherbolock countertops?

Download Commodity

Download Article

Butcher cake is a popular type of wooden kitchen counter. If you're having butcher block counters installed, you'll need to stain the wood to protect it and enhance it appearance. Likewise stain your butcher cake if you've had your counters for several years and the electric current finish is looking worn or faded. Sand the wood before staining, then select a wood stain and apply at to the lowest degree 2 coats. Then cease the stain with a coat of tung oil or other nutrient-safe sealant.

1. ane

   Sand the wood with coarse 80-dust sandpaper. Coarse sandpaper will remove whatsoever prior stains or varnishes from the butcher block, as well equally any marks or scratches the wood has on the surface. Sand along the grain of the wood using long strokes.^[one]

2. 2

   Sand the wood again with 150-grit sandpaper. As when using the fibroid-dust newspaper, sand the surface using long strokes in the aforementioned direction every bit the wood grain. Fine-grit paper will remove any marks left by the coarse sandpaper and prepare the forest to receive the stain.^[ii]

   • Use a newspaper towel or clean rag to wipe off the grit left behind subsequently sanding.

   Advertisement

3. iii

   Brush on 1 layer of wood conditioner. Apply a 3 inches (7.6 cm) paintbrush to apply an even layer of conditioner across the entire surface of butcher block. Paint in long, even strokes that parallel the management of the wood blocks.^[3] Give the conditioner at least 2 hours to dry.

   • If y'all're using a water-based stain, use a water-based conditioner. Also, if y'all plan to use an oil-based stain, buy an oil-based conditioner. You can buy wood conditioner at your local paint store.
   • Butcher block is composed of many pieces of wood, each with their own singled-out color. Applying forest conditioner before yous stain volition help all the pieces of woods accept on a like tone once the stain is applied.

4. four

   Sand the butcher block a final fourth dimension with 220-grit sandpaper. One time the conditioner has stale, become over the unabridged surface of the butcher block with very fine sandpaper. Every bit before, use long strokes in the direction that the blocks are laid. Exist certain to remove any splotches or discoloration caused by the conditioner.^[four]

   • Use a make clean rag to wipe off the fine dust left from sanding.
   • If you're tired of sanding by hand, yous tin hire an electrical sander from a local hardware shop.

   Advertisement

1. 1

   Choose a h2o- or oil-based wood stain in the color you lot prefer. Oil-based stains are longer lasting and more stain resistant. They also penetrate more than deeply into the wood. Water-based stains are generally quicker to apply. Decide which y'all want to utilise, then bring dwelling house a few color swatches to determine which you prefer.^[5]

   • Some people prefer a nighttime, walnut-color stain, while others opt for a red carmine-color stain, or a light, pine-colored stain.
   • Keep in mind that the color you lot choose should complement the other wood and cabinets in your kitchen.

2. ii

   Test the stain on a pocket-sized section of the butcher cake. Use a fresh 3 inches (7.6 cm) paintbrush to employ a unmarried blanket of stain to an out-of-the-mode section of your butcher block. Coat the woods generously, as if you were staining the bodily countertop.^{[half dozen]}

   • If accept any leftover chunks of butcher block that aren't attached to the counter (e.g., leftover from when it was installed), test the stain on this forest.

3. 3

   Let the stain dry for 2 hours and inspect the color. If the woods has an even, consistent color and the stain brings out the texture of the wood grain, you're set to stain the entire counter.^[7]

   • If the stain looks splotchy or has given the wood different tones, try a different brand or color of stain.

4. iv

   Paint on a layer of stain parallel to the direction of the boards. Dip your paintbrush in the tin can of stain, and tap it against the side to remove excess stain. Apply stain to every surface of the butcher cake: superlative, sides, and bottom (if any wood overhangs the cabinets below the butcher block). Pigment in long strokes that keep with the direction of the wooden slats.^[8]

5. 5

   Let the stain dry for at least viii hours. Give the stain plenty of fourth dimension to dry before you apply a 2nd layer. Avoid touching or setting any objects on the wet stain during this time.^[9]

6. half dozen

   Utilize a 2nd layer of stain to the butcher block. As before, apply the stain with a paintbrush using long strokes that go with the management of the forest grain. The second glaze will farther darken the forest, and ensure that the top of the butcher block is protected against scratches. Allow the stain to dry out overnight.^[10]

   • If any backlog stain is puddled on the surface later the cake dries overnight, use a dry out rag to wipe off.
   • If you'd similar the butcher block to be darker still, utilize a tertiary layer of stain.

   Advertisement

1. 1

   Buy 100% tung oil from a local paint shop. To ensure that you lot're purchasing pure tung oil, look for the words "100% tung oil" printed somewhere on the container'due south packaging. You can find tung oil at a local paint shop or hardware shop.

   • ane quart (0.95 L) of tung oil or Waterlox volition cover about 15 feet (4.6 m) of butcher block.
   • If y'all'd rather apply a longer-lasting product than tung oil, you tin can seal the butcher cake using a more substantial chemical sealant, similar Waterlox. Both products are food-condom.

2. 2

   Apply a layer of tung oil to seal the stained butcher block. Dip a clean, dry out cotton cloth or rag into the container of tung oil or Waterlox. And so utilise the cloth to rub the sealant across the surface of the stained butcher block. Work in long, straight strokes that parallel the direction of the boards in the butcher block.^[eleven]

   • Give the sealant a total 12 hours to dry.

3. 3

   Utilise 4 additional layers of tung oil to the butcher cake. Sealing the butcher cake is a time-consuming process. Information technology will need several layers of tung oil or Waterlox. Employ the same method for each layer: saturate a clean rag with sealant then rub it along the surface of the butcher cake. Apply a clean material to remove any excess sealant.^[12]

   • Ensure that each layer has at least 12 hours to dry earlier applying the subsequent layer.

4. 4

   Give the tung oil a full week to dry out. Avoid using the counter for 7 total days so the oil has enough time to fully soak into the woods. Once the week has passed, you tin can use your stained butcher block counters.

   • You tin still apply your butcher block countertops earlier a full week passes. Nevertheless, they'll exist oily and may stain your dishes or dress.

5. 5

   Put on a new layer of tung oil every 4 months. Tung oil wears off eventually, at which time it needs to be replaced. Every 4 months—or equally presently as the surface of the butcher block begins to await faded—apply a layer of tung oil to the wood.

   • The additional coats of oil won't take a full week to dry. To be on the safe side, though, give each layer iii-iv days before using the countertops.

   Advertizing

Ask a Question

200 characters left

Include your email address to go a message when this question is answered.

Submit

Advert

• Popular and common brands of wood stain include Behr, Rustoleum, Early American, and Minwax.

Cheers for submitting a tip for review!

Advertisement

Things Yous'll Need

• Wood stain
• Wood conditioner
• 2 3 inches (7.half dozen cm) paintbrushes
• 80-grit sandpaper
• 150-dust sandpaper
• 220-grit sandpaper
• Tung oil or Waterlox sealant
• Soft cloths or rags

About This Commodity

Article Summary X

To stain your butcher block, start by sanding the surface with a coarse sandpaper, which will remove any stains or varnishes. And so, sand the block once more with a fine-grit newspaper to remove whatever marks left by the coarser sandpaper. After you wipe off any grit, brush on 1 layer of wood conditioner. After the conditioner dries, which typically takes 2 hours, sand the block one last time with a very fine sandpaper to remove any splotches or discoloration from the conditioner. Adjacent, paint a layer of stain in long strokes forth the management of the wooden slats. Permit the stain dry for 8 hours before applying the next layer. When the stain is completely dry out, seal your butcher block by applying five layers of tung oil., Allow each layer to dry for a total 12 hours earlier using a rag to apply the adjacent coat. To learn how to selection the right stain for your butcher block, keep reading!

Did this summary assistance you lot?

Thanks to all authors for creating a page that has been read 187,873 times.

Did this article help you?

mcmillanbultempap.blogspot.com

Source: https://www.wikihow.com/Stain-Butcher-Block

Share this post